collapse

Search


User Info

 
 
Welcome, Guest. Please login or register.
Did you miss your activation email?

Author Topic: How To Reset Your Cisco 2960 Switch Password  (Read 27965 times)

Bejiening

  • Guest
How To Reset Your Cisco 2960 Switch Password
« on: November 26, 2013, 01:39:25 AM »
With many cisco switch user have this problem for a long time. This article is in order to help them solve this problem with an easy method.

Easy way to reset Cisco 2960 switch password:
First, power off your Cisco 2960 switch by unplugging its cord. As you reconnect the switch to the power source, press and hold the "Mode" button. On Cisco 2960 switches, this button is located on the front of the switch, on the left hand side.

After three seconds, the LED above the button should change from amber to green and start blinking. You are supposed to hold down the button until the light stops flashing. Release the button.

After you had done those steps, you can reset your password.
« Last Edit: November 26, 2013, 09:13:49 AM by MC »

Offline MC

  • Global Moderator
  • Cisco Guru
  • *****
  • Posts: 401
  • Reputation: 606
  • CCIE x3 (RS,Sec,SP)
  • Certification: CCIE
Re: How To Reset Your Cisco 2960 Switch Password
« Reply #1 on: November 26, 2013, 04:01:14 PM »
For the sake of completion, the method above only gets you into the rommon. You still need to modify the config-register by entering 'confreg' and follow wizard to ignore the startup config.

Offline adecisco

  • Cisco Newbie
  • *
  • Posts: 96
  • Reputation: 10
  • Discovering new solution is sweet!
    • http://adeolaade.blogspot.com/
  • Certification: N/A
Re: How To Reset Your Cisco 2960 Switch Password
« Reply #2 on: November 26, 2013, 10:26:51 PM »
MC,

From experience you do not need to modify config-reg for switches. Once you rename config.text that is all.

Beside you still need to modify the following:

flash_init

wait for the output then;

load_helper

after you can check for the switch directory to be sure of the file you are modifying.

dir flash:

What you are looking for inside the flash is:

4    -rwx  1131      <date>               config.text

After this you rename config.text to something else for example:

rename flash:config.text flash:config.old

Then enter this command to boot the switch;

boot

Once done you are good to go as you will be take to initial setup mode.

Hope this helps and round up the topic well.

The link below should help better:

You are not allowed to view links. Register or Login


Regards,
« Last Edit: November 26, 2013, 10:38:15 PM by adecisco »
Technology makes life easy but I hope the same technology will not send man back to stone age!

Offline MC

  • Global Moderator
  • Cisco Guru
  • *****
  • Posts: 401
  • Reputation: 606
  • CCIE x3 (RS,Sec,SP)
  • Certification: CCIE
Re: How To Reset Your Cisco 2960 Switch Password
« Reply #3 on: November 27, 2013, 09:13:51 AM »
 ;D You are correct.. I must have thought of the 4500.  Thanks for the correction.

Offline adecisco

  • Cisco Newbie
  • *
  • Posts: 96
  • Reputation: 10
  • Discovering new solution is sweet!
    • http://adeolaade.blogspot.com/
  • Certification: N/A
Re: How To Reset Your Cisco 2960 Switch Password
« Reply #4 on: November 27, 2013, 01:30:19 PM »
You are welcome that is why we are here to share knowledge  ;)
Technology makes life easy but I hope the same technology will not send man back to stone age!

Offline EMMANUEL HADJOR

  • Cisco Newbie
  • *
  • Posts: 1
  • Reputation: 0
  • Certification: N/A
Re: How To Reset Your Cisco 2960 Switch Password
« Reply #5 on: March 06, 2014, 09:09:03 AM »
You are not allowed to view links. Register or Login
You are welcome that is why we are here to share knowledge  ;)
You are not allowed to view links. Register or Login
MC,

From experience you do not need to modify config-reg for switches. Once you rename config.text that is all.

Beside you still need to modify the following:

flash_init

wait for the output then;

load_helper

after you can check for the switch directory to be sure of the file you are modifying.

dir flash:

What you are looking for inside the flash is:

4    -rwx  1131      <date>               config.text

After this you rename config.text to something else for example:

rename flash:config.text flash:config.old

Then enter this command to boot the switch;

boot

Once done you are good to go as you will be take to initial setup mode.

Hope this helps and round up the topic well.

The link below should help better:

You are not allowed to view links. Register or Login


Regards,

 

Related Topics

  Subject / Started by Replies Last post
1 Replies
24209 Views
Last post November 01, 2013, 04:02:15 AM
by adecisco
3 Replies
62227 Views
Last post April 19, 2018, 12:23:39 AM
by Kaikagaga
3 Replies
41812 Views
Last post August 16, 2016, 11:21:54 PM
by MC
3 Replies
50576 Views
Last post June 24, 2018, 07:46:41 PM
by pinyowit
2 Replies
22656 Views
Last post January 10, 2021, 03:25:08 PM
by MC

SimplePortal 2.3.7 © 2008-2024, SimplePortal